Mazda 626

1991-1998 of release

Repair and car operation



Mazda 626

+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Heating and ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Running gear
+ 11. Body
- 12. Electric equipment
   12.1. Introduction
   12.2. Search of a source of malfunction in electric equipment system
   12.3. Safety locks
   12.4. Automatic switches
   12.5. Relay
   12.6. Breaker of indexes of turns / alarm system
   12.7. Switches on a steering column
   12.8. Switch of ignition and lock drum
   12.9. Switches on the dashboard
   12.10. Tools of an instrument guard
   12.11. Instrument guard
   12.12. Radio receiver and loudspeakers
   12.13. Aerial
   12.14. Bulbs of headlights of head light
   12.15. Headlights of head light
   12.16. Drive of headlights of head light
   12.17. Replacement of bulbs
   12.18. Engine of screen wipers
   12.19. Horn of a sound signal
   12.20. System of day inclusion of headlights
   12.21. Heater of back glass
   12.22. System cruise control
   12.23. Electric window regulators
   12.24. Central lock and remote control by the central lock
   12.25. A rear-view mirror with the electric drive
   12.26. Top hatch
   12.27. Safety airbag
+ 13. Electroschemes
+ 14. Good advice



12.17. Replacement of bulbs

Forward indexes turns / front position lamps

PERFORMANCE ORDER
1. On the Ford Probe models turn off fixing screws and unbend edge of an insert of a wheel niche for access to a bulb.
2. On the Ford Probe models turn counter-clockwise and remove a cartridge with a bulb of the index of turns (And) and a front position lamp (In).
3. On the Mazda models turn off a fixing bolt (it is specified by an arrow) and remove the index of turns. Turn a cartridge with a bulb and get it from a headlight.
4. Replace a bulb.
5. Installation is carried out upside-down removals.

Back indexes of turns, fires of a stoplight and marker lights

PERFORMANCE ORDER
1. Open a luggage carrier cover / a back door.
2. On the Probe models turn off the top fixing screw (a photo at the left) and take a block headlight (a photo on the right).
3. On the Mazda models unbend the panel of furnish and turn off fixing screws of the holder of bulbs.
4. Turn a cartridge with a bulb counter-clockwise and get a cartridge. Replace a bulb.
5. Installation is carried out upside-down removals.

Top lamp of a stoplight

PERFORMANCE ORDER
1. Open a back door / trunk lid.
2. On the Probe models remove lateral panels of furnish, then remove a plastic pin (it is specified by an arrow) and remove the central panel.
3. Get cartridges with bulbs (are specified by shooters)
4. On the Mazda models wring out a plastic latch (it is specified by an arrow) and remove a lamp casing.
5. Get a cartridge and replace a bulb.
6. Installation is carried out upside-down removals.

Bulbs of illumination of registration plate

PERFORMANCE ORDER
1. Remove two lamps of illumination of registration plate.
2. Replace bulbs.

Bulbs of illumination of salon

PERFORMANCE ORDER
1. Remove rasseivatel for access to bulbs (are specified by shooters).
2. Remove a rasseivatel for access to a bulb (it is specified by an arrow).
3. Turn off the fixing screw (it is specified by an arrow) and remove a rasseivatel.
4. Remove a rasseivatel.
5. Replace bulbs.

Bulbs of illumination of an instrument guard

PERFORMANCE ORDER
1. Remove an instrument guard.
2. Turn a cartridge with a bulb counter-clockwise and remove it from an instrument guard.
3. Replace a bulb.
4. Installation is carried out upside-down removals.