Mazda 626

1991-1998 of release

Repair and car operation



Mazda 626

+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Heating and ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Running gear
+ 11. Body
- 12. Electric equipment
   12.1. Introduction
   12.2. Search of a source of malfunction in electric equipment system
   12.3. Safety locks
   12.4. Automatic switches
   12.5. Relay
   12.6. Breaker of indexes of turns / alarm system
   12.7. Switches on a steering column
   12.8. Switch of ignition and lock drum
   12.9. Switches on the dashboard
   12.10. Tools of an instrument guard
   12.11. Instrument guard
   12.12. Radio receiver and loudspeakers
   12.13. Aerial
   12.14. Bulbs of headlights of head light
   12.15. Headlights of head light
   12.16. Drive of headlights of head light
   12.17. Replacement of bulbs
   12.18. Engine of screen wipers
   12.19. Horn of a sound signal
   12.20. System of day inclusion of headlights
   12.21. Heater of back glass
   12.22. System cruise control
   12.23. Electric window regulators
   12.24. Central lock and remote control by the central lock
   12.25. A rear-view mirror with the electric drive
   12.26. Top hatch
   12.27. Safety airbag
+ 13. Electroschemes
+ 14. Good advice


12.22. System cruise control

GENERAL INFORMATION

The system cruise control supports the set speed of movement of the car by means of the electronic control unit, the sensor of speed and a drive located in an impellent compartment. The system cruise control consists of switches, the sensor of speed, the switch of fires of a stoplight, the switch on a pedal of coupling and connecting wires.

Identification of plugs and conductivity check (between plugs 2 and 3) the system switch cruise control – the Ford Probe models

Position of the switch
Resistance (Ohm)
On
10000
Off
Less than 5
Set/Acc
680
Coast
120
Resume
2200

Identification of plugs of the main switch of system cruise control – the Mazda models

At inclusion between plugs C and D there should be a conductivity.

Codes of malfunction of system cruise control of the Mazda models


Code
Possible reason
1
Connecting wires, system drive, switch of fires of a stoplight
5
Safety lock
7
Switch of fires of a stoplight
11
System switch cruise control
15
Electronic control unit

Check
PERFORMANCE ORDER
1. Check a system safety lock cruise control.
2. Check operation of the switch of fires of a stoplight.
3. Check operation of the switch on a coupling pedal.
4. Examine vacuum hoses and check a tension of a rope of system.
5. Check the sensor of speed.

System switches cruise control

Check and replacement

Ford Probe models

PERFORMANCE ORDER
1. Remove switches and check them on conductivity (see fig. Identification of plugs and conductivity check (between plugs 2 and 3) the system switch cruise control – the Ford Probe models).
2. Remove the module of an airbag of safety.
3. Turn off fixing screws disconnect sockets of connection and remove switches.
4. Installation is carried out upside-down removals.

Mazda models

On these models system cruise control has the built-in system of diagnostics.

PERFORMANCE ORDER
1. For activation of system of diagnostics include ignition and press the Resume/Accel button for three seconds.
2. In two seconds after an alarm bulb of system cruise control on the dashboard will go out, the malfunction code (see tab. will be deduced. Codes of malfunction of system cruise control of the Mazda models).
3. Remove the system switch cruise control and check it on conductivity (see fig. Identification of plugs of the main switch of system cruise control – the Mazda models).
4. For replacement of the switch located on a steering column, look points (see tab. Codes of malfunction of system cruise control of the Mazda models).
5. For replacement of the main switch of system cruise control remove the switch from the dashboard and disconnect the connection socket.
6. Installation is carried out upside-down removals.

Adjustment of a tension of a rope

PERFORMANCE ORDER

Remove a fixing clip (And) and adjust a rope tension so that it had a free wheeling in 3 mm in a point (In).